Instruction ManualUnderwater CasePT-023For the digital cameraCAMEDIA C-8080 Wide Zoom Thank you for buying the Underwater Case PT-023. Please read t
E-91. PreparationsCheck the contents of the package.Check that all accessories are in the box.Contact your dealer if accessories should be missing or
LCD hood strapGrease for O-rings (White-cap tube)Silica gelBalance weightPick for removing O-ringsBuckle openerLens capBuckle open/close leverBuckle h
E-11: •Do not exert excessive force onto the lens window or the lens ring.• Take care not to put your fingers etc. over the lens windowand the flash
E-12How to Press the ShutterWhen pressing the shutter lever,press it gently, so that there willbe no movement of the camera.Note: • For more detailed
E-13Setting the Zoom LeverWhen loading the digital camera in theCase, fit the projecting part of the zoomlever of the digital camera into therecessed
BossBuckleE-14: •If the standard port is attached improperly to the case,water penetration may result. Also make sure that thebuckles on the left and
E-15: •The diffusion plate cannot be used when the PPO-05is mounted.CAUTIONDetachingFirst make sure the case is completely dry. Whilegently holding th
E-16Removing the TTL cable connector capTTL flash shooting is possible by uncapping the TTL cable connectoron this case (PT-023) and connecting the FL
E-17Removing the hot shoe cable capTo perform TTL flash shooting when this case is used, connect thehot shoe cable provided with the optional PFL-01 b
E-182. Advance Check of the CaseAdvance test before useThis Case has been the subject of thorough quality control for the partsduring the manufacturin
E-1Disclaimer● Unauthorised copying of this manual in part or in full, except forprivate use, is prohibited. Unauthorised reproduction is strictlyproh
E-19Advance Test1. Before installing the digital camera in the Case, immerse the emptyCase to the intended water depth to confirm that there is no wat
E-203. Install the digital camera.Check the digital camera.Check the digital camera before loading it in the Case.Battery ConfirmationSince the LCD mo
① ② E-21Lifting the mode dial knobPull up the mode dial of the case until itstops, so that it does not interfere with themode dial of the digital came
E-22Fitting the mode dial knobAfter the digital camera has been loaded, pushdown the mode dial of the case from the uppersurface of the case and set i
E-23: •Seal the Case by turning both buckle lock levers down inarrow direction. When one of the buckles is left open, theCase will not be sealed and w
GuidesE-24Installation and Removal of the LCD HoodInstallationStrongly push the mounting projections of the LCD hood as shownin the figure into the gu
E-25: •After inserting the camera into the case, confirm that themode dial moves. If it does not move, oil or grease mayhave gotten on the mode dial.
E-26Final TestThe final test after loading the camera is explained below. This is the only way toeliminate worry about possible entry of water! Always
E-274. Taking Pictures Under WaterHow to Use the Hand StrapPass your hand through theaccessory hand strap andadjust the length with thestop button.Tak
E-285. Handling After ShootingWipe off any waterdrop.After underwater shooting,remove any drops of water fromthe case. Use pressurized air ora soft, l
E-21. Keep this product out of the reach of babies, infants, and children.There is the possibility of occurrence of the following types ofaccidents.
E-29Take out the digital camera.Open the case carefully, pull up the mode dial from the upper surface ofthe case to disengage it from the mode lever o
E-30Wash the Case with pure water.After use, seal the Case again after taking out the camera and wash itsufficiently in pure water as soon as possible
E-316. Maintaining the Waterproof FunctionRemove the O-ring.Open the Case and remove the O-ring from the Case.Removal of the O-ring Insert the O-ring
E-32Install the O-ring.Confirm that no foreign matter is attached, apply a thin coat of theaccessory grease to the O-ring, and fit the O-ring into the
E-33: •Always perform maintenance of the waterprooffunction even when the Case has been opened toexchange the battery or the image storage duringshoot
E-34Replace consumable products. The O-ring is a consumable product. Independent of the number oftimes the Case is used, it is recommended that the O
E-357. AppendixQ & A on the use of the PT-023Q1 : Which digital cameras can be used with this case?A1 : This case is designed exclusively for use
E-36(a) Places where the Case can reach high temperatures under directsunlight or in a car, places with extremely low temperatures, andplaces with ext
E-37moisture and dry the Case in the shade. Do not use hot air from a hairdrier or the like and do not dry the Case under direct sunlight. Exposureto
E-38(3) Damage, deterioration, or deformation of the O-ring(4) Sand, fibers, hair or other foreign matter on the O-ring(5) When foreign matter (sand,
E-3Batteries● Use an exclusive lithium-ion battery (Olympus BLM-1) designed fordigital cameras.● Keep the battery's contacts away from damp or hu
E-39is sufficient for cleaning.•Do not use anticorrosion agents on the metal parts. The metal parts aremade of aluminum, brass or stainless steel. Cle
E-40After-sale Service● You will receive the Warranty card from your dealer. Please makesure that the dealer's name, the date of purchase, etc. h
E-41Olympus digital camera CAMEDIA C-8080 Wide ZoomAvailable modelsDimensionsE-41Specifications❈ We reserve the right to change the external appearanc
E-4For Prevention of Water Leakage AccidentsWhen water leakage occurs while this product is being used, repair ofthe camera housed in this product may
E-5Handling the Product● Use or storage of the product at the following locations may causedefective operation, defects, trouble, damage, fire, intern
E-6● Do not perform operations other than specified in this instructionmanual, do not remove or modify parts other than specified, and donot use parts
E-7Disclaimer ......E-1Please read the following before using the product
E-8Fitting the mode dial knob ..............E-22Insertion of silica gel...........
Comments to this Manuals