Olympus FL-20 User Manual download pdf

Battery Warnings

For customers in USA

Declaration of Conformity

Model Number : FL-20

Trade Name : OLYMPUS

Responsible Party : Olympus America Inc.

Address : 2 Corporate Center Drive, Melville, New York

11747-3157 U.S.A.

Telephone Number : 1-631-844-5000

Tested To Comply With FCC Standards

FOR HOME OR OFFICE USE

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

For customers in Canada

This Class B digital apparatus meets all requirements of the

Canadian Interference-Causing Equipment Regulations.

For customers in Europe

“CE” mark indicates that this product complies with the

European requirements for safety, health, environment and

customer protection. “CE” mark flashes are intended for

sales in Europe.

INSTRUCTIONS

Please read these instructions carefully before using your flash.

ENGLISH

ELECTRONIC

FLASH

FL-20

http://www.olympus.com/

Cameras That the Flash

Can Be Attached to

Some functions available

are limited depending on

models of cameras even

manufactured by

Olympus.

Printed in Japan 0103 2MJ

Warning

Caution

Safety Precautions

In order to obtain optimum performance and a longer service life from your new flash unit, please read

these instructions carefully. Always keep this leaflet in a readily accessible place for later reference. To

prevent potential hazards that could cause injury or damage to property, always pay close attention to

the important remarks indicated with the symbols and terms below.

Ignoring this warning and using the unit incorrectly could result in

serious injury.

Ignoring this warning and using the unit incorrectly could result in death

or serious injury.

BATTERIES MAY LEAK, GENERATE HEAT, IGNITE,

OR EXPLODE.

Do not use batteries not specified for this product.

Do not try to recharge non-rechargeable batteries.

Do not throw batteries into fire, expose them to excessive

heat, or short-circuit them.

Do not mix new and old batteries or different brands of

batteries.

Do not place the batteries with the or terminals facing

the wrong direction.

CHILDREN MAY SWALLOW BATTERIES.

Keep batteries out of the reach of children. If a child swallows a

battery, contact a doctor immediately.

Pay attention.

Prohibited.

Do not touch.

Do not disassemble.

General Warnings

Do not point the flash at a driver or

rider of a vehicle (bicycle, automobile,

train, etc.) and fire the flash. This may

cause a traffic accident. Turn off the

flash or make sure the flash does not

fire before shooting this kind of

subject.

Do not fire the flash close to the eyes

of a human or animal. Eyesight may

be temporarily impaired.

Flash Warnings

If an internal component is exposed because the unit was dropped or otherwise damaged:

① Never touch the exposed component.

② Immediately remove the batteries, being careful not to expose yourself to electric shock, burn yourself, or

otherwise injure yourself,

③Send the unit to your camera store or Olympus service center. The unit contains a high-voltage circuit that

could cause electric shock, burn you, or otherwise injure you.

Do not try to disassemble, repair, or modify the unit. The unit contains a high-voltage circuit that may cause

electric shock, burn you, or otherwise injure you.

Do not activate the flash when your skin or other object is in contact with the flash reflector. Do not touch the

flash reflector after the flash has fired repeatedly. You may burn yourself.

Do not use the unit near flammable gas or substances (such as gasoline, benzine, or thinner). This can cause

explosion or fire.

If the unit is dropped in water, or if water, metal particulate, a flammable foreign object gets into the unit:

① Remove the batteries immediately.

② Send the unit to your camera store or Olympus service center. Using the unit in this condition may cause fire

or electric shock.

Do not wet the unit or touch the unit with wet hands. This could cause electric shock.

Specifications

Guide number

Standard — GN20 (ISO100

・

m).

GN66 (ISO100

・

ft).

With wide-angle converter — GN14 (ISO100

・

m).

GN46 (ISO100

・

ft).

Illumination angle

Standard — Covers the image angle of a 35 mm lens

(assuming the use of 35 mm film).

With wide-angle converter — Covers the image angle

of a 24 mm lens.

Color temperature

5500°K

Flash duration

Approx. 1/30000 to 1/1200 sec.: AUTO modes.

Approx. 1/1200 sec.: MANUAL mode.

Maximum number of flashes

Approx. 250 times (when using two AA alkaline

batteries (LR6))

Required charge time

Approx. 0.5 to 5.0 sec. (when using two AA alkaline

batteries (LR6))

Flash modes

①TTL AUTO. ②AUTO. ③MANUAL.

Power supply

AA alkaline batteries (LR6), lithium batteries (FR6),

nickel-manganese batteries (ZR6D), NiMH batteries,

NiCd batteries, x 2

Dimensions & weight

W56 x H96 x D28 mm (2.2" x 1.1" x 3.8" ), approx. 74 grams

(2.6 oz) (excluding batteries)

Accessories

Wide panel, soft case

• The values above are typical at normal temperature (20°C /

68°F). (The maximum number of flashes and required

charge time were measured at our in-house test conditions.)

Actual values may vary depending on the batteries used and

ambient temperatures.

Design and specifications are subject to change

without any notice or obligation on the part of the

manufacturer.

Names of Parts/Attaching the Wide Panel

（Front）



Flash tube



Photoelectric sensor window



Shoe lock dial

（Rear）



TEST button



Battery compartment cover



AUTO CHECK lamp:

Blinks when flashing light intensity is optimum.



CHARGE lamp



Mode dial (Power/Mode switch)



Exposure table



Wide panel

The wide panel covers an angle equivalent to a 24 mm

wide-angle lens assuming the use of a 35 mm film.

Loading Batteries/Test Flashing





Batteries

Insert two “AA”-size alkaline batteries, lithium

batteries, nickel-manganese batteries, NiMH

batteries or NiCd batteries as shown in the

illustration.

Note that “AA”-size manganese(zinc-carbon)

batteries cannot be used.



Set the Mode dial to AUTO.



When the CHARGE lamp lights up, press the TEST

button and confirm flashing.

Mounting the Flash on the Camera

If the camera is equipped with a

hot shoe, mount the flash directly

on the hot shoe.

If the camera is equipped with an

external flash terminal, mount the

flash using the flash bracket and

bracket cable.

You cannot use the FL-20 flash if

the camera is not equipped with a

hot shoe or external flash terminal.

Mounting the Flash on a Hot Shoe



Slide the flash all

the way into the

hot shoe.



Turn the shoe

lock dial to secure

the flash in place.





TTL AUTO Operation

AUTO Operation MANUAL Operation

Set the FL-20’s Mode dial to TTL AUTO and set the

camera’s MODE DIAL to or .

In the TTL AUTO mode, the flash adjusts the light

intensity automatically according to changes in the

camera’s aperture. (TTL AUTO mode operation

requires that the camera’s mode is set as shown in

the above illustration.)

If the camera is not set correctly, the CHARGE lamp

blinks.

The AUTO CHECK lamp will blink when the flash illumination reaches optimum intensity. If the

AUTO CHECK lamp does not blink, move closer to the subject or reduce the camera’s aperture.

The AUTO CHECK lamp does not blink on the following models (as of January, 2003):

C-4000ZOOM, C-4040ZOOM, C-3000ZOOM, C-3040ZOOM, C-2040ZOOM

When the wide panel is used, use the approx. 0.7X distances shownabove as reference.

The above distances may become shorter with some models.

When the wide panel is used, use the approx. 0.7X distances

shownabove as reference.

The above distances may become shorter with some models.

f-stop

ISO speed

Camera aperture numbers and applicable shooting ranges

1.4 2 2.8 4 5.6 8 11 16

100

2.0 – 14 1.4 – 10 1.0 – 7.1 1.0 – 5.0 1.0 – 3.5 1.0 – 2.5 1.0 – 1.8 1.0 – 1.3

6.6 – 45.9 4.6 – 32.8 3.3 – 23.3 3.3 – 16.4 3.3 – 11.5 3.3 – 8.2 3.3 – 5.9 3.3 – 4.3

200

2.8 – 20 2.0 – 14 1.4 – 10 1.0 – 7.0 1.0 – 4.9 1.0 – 3.5 1.0 – 2.5 1.0 – 1.8

9.2 – 65.6 6.6 – 45.9 4.6 – 32.8 3.3 – 23.0 3.3 – 16.1 3.3 – 11.5 3.3 – 8.2 3.3 – 5.9

400

4.0 – 28 2.8 – 20 2.0 – 14 1.4 – 10 1.0 – 7.1 1.0 – 5.0 1.0 – 3.5 1.0 – 2.5

13.1 – 91.8 9.2 – 65.6 6.6 – 45.9 4.6 – 32.8 3.3 – 23.3 3.3 – 16.4 3.3 – 11.5 3.3 – 8.2

800

5.6 – 40 4.0 – 29 2.8 – 20 2.0 – 14 1.4 – 10 1.0 – 7.1 1.0 – 5.0 1.0 – 3.6

18.4 –131.1 13.1 – 95.1 9.2 – 65.6 6.6 – 45.9 4.6 – 32.8 3.3 – 23.3 3.3 –16.4 3.3 –11.8

Set the FL-20’s Mode dial to AUTO, set the camera’s

MODE DIAL to and adjust the camera’s aperture.

The aperture setting varies depending on the ISO

speed set to the camera (see table).

In the AUTO mode, the flash adjusts the light

intensity automatically regardless of the distance to

the subject.

The AUTO CHECK lamp will blink when the flash

illumination reaches optimum intensity. If the AUTO

CHECK lamp does not blink, move closer to the

subject.

ISO speed Aperture

100 2.8

200 4

400 5.6

800 8

Camera’s ISO speeds and apertures

Effective flash distance:

1 to 7.1 m / 3.3 to 23.3 ft

(0.7 to 4.9 meters / 2.3 to 16.4 ft

when the wide panel is used)

Set the FL-20’s Mode dial to MANUAL, set the

camera’s MODE DIAL to and adjust the

camera’s ISO speed, aperture and shutter speed.

The flash emits light at the maximum intensity.

The AUTO CHECK lamp does not blink in this

mode.

f-stop

ISO speed

Optimum shooting ranges

GN 1.4 2 2.8 4 5.6 8 11 16

100

14 10 7.1 5.0 3.5 2.5 1.8 1.3

45.9 32.8 23.3 16.4 11.5 8.2 5.9 4.3

200

20 14 10 7.0 4.9 3.5 2.5 1.8

65.6 46.0 32.8 23.0 16.1 11.5 8.2 5.9

400

28 20 14 10 7.1 5.0 3.5 2.5

91.8 65.6 45.9 32.8 23.3 16.4 11.5 8.2

800

40 29 20 14 10 7.1 5.0 3.6

131.1 95.1 65.6 45.9 32.8 23.3 16.4 11.8

Aperture calculation formula (ISO 100)

Aperture (F) = Guide Number (GN)/Range (in meters)

Indicator Lamps

The following lamps indicate the flash status.

AUTO CHECK

lamp

Communication errors

When the FL-20 mode is; TTL AUTO: Error communicating with the camera.

(The camera is OFF, set to the wrong mode, etc.)

The CHARGE lamp blinks when the camera’s LCD monitor is turned off on the following models

(as of January, 2003):

C-4000ZOOM, C-4040ZOOM, C-3000ZOOM, C-3040ZOOM, C-2040ZOOM.

CHARGE lamp OFF ON

Regular blinking

OFF

Under charge Charge completed Communication error

Blinking

Optimum light intensity

–

Low battery warning

Customer support (Japanese language only):

Tel. 0426-42-7499 Tokyo

OLYMPUS OPTICAL CO., LTD.

Two Corporate Center Drive, Melville, NY 11747-3157, U.S.A.

Tel. 631-844-5000

Technical Support (USA)

24/7 online automated help: http://support.olympusamerica.com/

Phone customer support: Tel. 1-888-553-4448 (Toll-free)

Our phone customer support is available from 8 am to 10 pm (Monday

to Friday) ET

E-Mail: [email protected]

Olympus software updates can be obtained at:

http://olympus.com/digital/

For customers in North and South America

OLYMPUS AMERICA INC.

Wendenstrasse 14-18, 20097 Hamburg, Germany

Tel. +49 (0)40-23 77 33

European Technical Customer Support:

Please visit our homepage http://www.olympus-europa.com

or call NUMBER : 00800 - 67 10 83 0 (Toll-free)

+49 (0)1805-67 10 83 or +49 (0)40-23 77 38 99 (Charged)

OLYMPUS OPTICAL CO. (EUROPA) GMBH.

VT455001

The above distances may become shorter

with some models.

1 2 3

ELECTRONIC 1

Summary of Contents

Page 1 - ELECTRONIC

Battery WarningsFor customers in USADeclaration of Conformity Model Number : FL-20Trade Name : OLYMPUSResponsible Party : Olympus America Inc.Addre

Page 2

Page 3

Comments to this Manuals

No comments

Olympus FL-20 User Manual

Browse online or download User Manual for Flashlights Olympus FL-20. Olympus FL-20 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Flashlights Olympus FL-20