Olympus 5060 User Manual

Owner’s Manualwww.uwimaging.com5060

(Fig. 16)(Fig. 15)(Fig. 14)(Fig. 13)11

Attaching Strobe Arm MountsIdentify all the parts in the strobe arm mount accessory kit. It should contain: Two basemounts, two hex keys, two small O-

(Fig. 23) (Fig. 24)(Fig. 21)(Fig. 20)(Fig. 19)13(Fig. 22)F = Ikelite 400– = Ikelite 200-1 = Ikelite DS-125– = Ikelite 100-2 = Ikelite DS-50– = Ikelite

Shooting the Tetra 5060ROC DefinedROC is a revolutionary new strobe controller that is built into the Tetra 5060 housing.ROC enables the photographer

If ROC is in stand-by mode and the shutter button is pressed, ROC will process theshutter command and return to the active status.ROC will turn off af

Shooting TechniquesDigital cameras have many features and controls that initially seem overwhelming. Thecontrols listed below are the most commonly ac

17(Fig. 30)(Fig. 29)(Fig. 28)(Fig. 27)(Fig. 26)(Fig. 25)

Replacing ROC Housing batteryROC will indicate a low battery status by flashing a slow red Status LED.1. Replacement battery type is CR2450 and can be

19Attaching a focus lightWhy use a focus light?Night diving , wreck diving, cave exploration or heavy kelp canopies are diving scenarioswhere ambient

20Installing Classic Light (Optional)Attach the battery pod to the bracket.1) Slide the raised pod detail through the T shaped channel of the bracket.

WelcomeCongratulations on your purchase of a Tetra 5060 digital still housing.Please inspect the packaging of your product to verify that there was no

21(Fig. 38)(Fig. 37)(Fig. 36)(Fig. 35)(Fig. 34)(Fig. 33)

22Lens Installation and RemovalTo remove the flat port1. Slide locking pin away from lens (Refer fig. 39)2. Rotate optic counter clockwise.3. Pull awa

23(Fig. 41)(Fig. 40)(Fig. 39)

After Diving Care1. Immediately submerge the housing in fresh water. While in fresh water, work the ModeDial, Zoom Lever and all the buttons, to work

25Tetra 5060 AccessoriesTetra 5060 Fault Free Warranty . . . . . . . . . . . . . . . . . .905-0200Tetra 5060 Wide-Angle Lens . . . . . . . . . . . .

26Returning Products for CareWe highly recommend a factory annual service to maintain properoperation of your Tetra Housing 1) Before returning your L

300 Cannery Row • Monterey, CA 93940(831) 645-1525 • Fax (831) 375-2517www.uwimaging.com905-0243-A

Table of ContentsGetting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Getting StartedIllustrated below are the locations of Tetra’s features, ports, and functions. Take time tofamiliarize yourself with the housing.5ROC S

First Time UseAll Light & Motion housings are pressure tested to 300 feet prior toshipping. However, there could be unseen damage from shipping. A

(Fig. 5)(Fig. 4)(Fig. 6)(Fig. 3)(Fig. 2)(Fig. 1)7

8Tetra 5060 ControlsTop Housing ControlsShutter-Release Button: Presses the camera’s shutter-release button.Press the button halfway for the camera to

(Fig. 12)(Fig. 11)(Fig. 10)(Fig. 9)(Fig. 8)(Fig. 7)9

Installing Bulkheads1. Remove bulkhead cap by inserting a coin into the slot in the cap and turning counter-clock wise (Refer fig. 13).2. Check the O-