Olympus PT-E05 User Manual Page 1

©2008 http://www.olympus.com/VS724601Printed in ChinaPT-E05取扱説明書デジタルカメラ 用防水プロテクターInstruction ManualUnderwater Case for digital cameraEn

EN 9EnInstall the Waterproof Port.To enable the Case to be used underwater, the separately available Waterproof Port for the camera lens must be insta

EN 10EnMastering basic Case operations.Before loading the digital camera, be sure you are comfortable with the basic Case operations.How to hold the C

EN 11EnWhether or not the Case’s zoom ring can control the camera’s zoom ring and focus ring depends on which lens is mounted on the digital camera. F

EN 12EnConnecting the underwater optical fiber cableRemoving the TTL cable connector capTo perform TTL flash shooting by connecting the separately ava

EN 13EnCleaning the TTL connectorIf the threaded sections of the TTL cable and TTL cable connector stick to each other, the cable may disconnect from

EN 14EnHow to attach and detach the camera tableThe camera table inside the front lid of the Case is used to load the digital camera into the Case.1 S

EN 15En2. Advance check of the CaseAdvance test before useThis Case has been the subject of thorough quality control for the parts during the manufact

EN 16En3. Installing the digital cameraCheck the digital camera.Check the digital camera before loading it in the Case.Battery ConfirmationUnderwater

EN 17EnRemove the filter from the digital cameraIf a filter is attached to the lens of the digital camera, remove the filter before loading the digita

EN 18EnAttach the zoom and focus gears provided with the optional underwater port to the lens.To control the zooming and manual focusing of the camera

EN 1EnIntroductionz Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strict

EN 19EnHow to attach the camera table to the digital cameraIn order to load the camera into the Case, attach the camera table (located on the front-li

EN 20EnUsing the electronic flash with the TTL cableTo attach the Electronic Flash to this Case using TTL cable, connect the hot shoe cable to the cam

EN 21EnInsert the digital camera in the Case.Load the digital camera in the Case after checking the following:• Is the digital camera turned OFF?• Is

EN 22En3 When using a slave flash from a non-Olympus manufacturer, push the # button on the camera to pop up its built-in flash.4 After attaching the

EN 23En5 When using an external electronic flash with a TTL cable, connect the hot shoe cable to the camera’s hot shoe and set the camera’s automatic

EN 24EnInsert the silica gelBefore sealing the Case, be sure to insert the silica gel bag in the space between the bottom of the camera table and the

EN 25EnSeal the Case.1 Close the rear lid gently (so that the O-rings do not slip out of the grooves).2 Turn the open/close dial clockwise.• The Case

EN 26EnCheck the operation of the loaded camera.After sealing the Case, check that the camera functions normally.• Operate the power switch lever on t

EN 27EnFinal TestThe final test after loading the camera is explained below. This is the only way to eliminate worry about possible entry of water! Al

EN 28En4. Underwater ShootingHow to use the hand strapAttach the hand strap to the Case, pass your right hand through the hand strap and hold the Case

EN 2EnWARNING1 Keep this product out of the reach of babies, infants, and children. There is the possibility of occurrence of the following types of a

EN 29En5. Handling After ShootingWipe off any waterdrop.After underwater shooting, remove any drops of water from the case. Use pressurized air or a s

EN 30EnUnload the digital camera.First, open the open/close dial of the Case and then open the rear lid carefully. Next, pull out the zoom dial and mo

EN 31EnWash the Case with pure water.After use, seal the Case again after taking out the camera and wash it sufficiently in pure water as soon as poss

EN 32En6. Maintaining the Waterproof FunctionRemove the O-ring.Open the Case and remove the O-ring.Procedure1 Insert the O-ring remover into the gap b

EN 33EnInstall the O-ring.Confirm that no foreign matter is attached, apply a thin coat of the accessory grease to the O-ring, and fit the O-ring into

EN 34EnReplace consumable products.• The O-ring is a consumable product. Independent of the number of times the Case is used, it is recommended that t

EN 35En7. AppendixQ & A on useQ1: : Which digital cameras can be used?A1: : This product (PT-E05) is exclusively for use with the E-520 Digital Ca

EN 36EnQ5: : What cautions must be observed when opening and closing the Case?A5: : Pay special attention to the following items.1 Do not open and clo

EN 37EnQ9: : What are the important points for O-ring maintenance?A9: : Pay special attention to the following items.1 Never use alcohol, thinner, ben

EN 38EnWaterproof PortWithstanding depthApplicable LensNotePPO-E01 60 m14-45 mmPackaged with the PPZR-E01 underwater zoom gear for 14-45 mm lens.35 mm

EN 3EnBatteriesz Use only with an Olympus lithium-ion rechargeable battery (BLM-1) specially for camera use.z Take care that the battery electrodes do

EN 39EnSpecifications* We reserve the right to change the external appearance and the specifications without notice.Available models Olympus Digital C

PT-E05_EN.Book Page 40 Wednesday, June 4, 2008 12:34 PM

©2008 http://www.olympus.com/VS724601Printed in ChinaPT-E05Jp取扱説明書デジタルカメラ 用防水プロテクターInstruction ManualUnderwater Case for digital cameraEnMode

EN 4EnHandling the Productz Use or storage of the product at the following locations may cause defective operation, defects, damage, fire, internal cl

EN 5EnIntroduction ... 1Pleas

EN 6EnInsert the silica gel ... 24Check the load

EN 7En1. PreparationsCheck the contents of the package.Check that all accessories are in the box.Contact your dealer if accessories are missing or dam

EN 8EnNames of the partsNote:Case operation parts marked by * corresponds to the operation parts of the digital camera. When the operation parts of th